EPF-Lausanne/30 July 2008

From 2008.igem.org

(Difference between revisions)
 
(12 intermediate revisions not shown)
Line 1: Line 1:
 +
[https://2008.igem.org/wiki/index.php?title=EPF-Lausanne/29_July_2008 <<Previous] - [https://2008.igem.org/Team:EPF-Lausanne/Notebook Back to Notebook] -
 +
[https://2008.igem.org/wiki/index.php?title=EPF-Lausanne/31_July_2008 Next>>]
 +
 +
==2 Step PCR Protocol==
<p>We started a 2 step PCR too get LuxR, lasR, RhlR genes. We intend to convert them to proteins invitro to test their binding affinity to their DNA sites.  
<p>We started a 2 step PCR too get LuxR, lasR, RhlR genes. We intend to convert them to proteins invitro to test their binding affinity to their DNA sites.  
1st step worked  except for LasR, but we were not sure the gene was actually in the plasmid. 2nd stop should finish this evening. We have to order the "ribosomal solution" to continue.
1st step worked  except for LasR, but we were not sure the gene was actually in the plasmid. 2nd stop should finish this evening. We have to order the "ribosomal solution" to continue.
We used more DNA and primers because 1st try didn't work. Here is our protocal. Normaly 1ul of DNA and primers.
We used more DNA and primers because 1st try didn't work. Here is our protocal. Normaly 1ul of DNA and primers.
</p>
</p>
-
<h3>Protocol</h3>
+
 
-
<h4>1st Step</h4>
+
===<h4>1st Step</h4>===
<table width="207" border="1">
<table width="207" border="1">
   <tr>
   <tr>
Line 43: Line 47:
   </tr>
   </tr>
</table>
</table>
-
<h4>2nd Step</h4>
+
===<h4>2nd Step</h4>===
<p>Dilute primers to 250nM each. The template is the previous PCR mix</p>
<p>Dilute primers to 250nM each. The template is the previous PCR mix</p>
<table width="207" border="1">
<table width="207" border="1">
Line 84: Line 88:
</p>  
</p>  
Same has to be done for incorporating RhlI in the GFP operon on the pHD plasmids. We may use PciI to cut the plasmid in one location: 3382. But we have to check if we were the terminator is. May have to digest out the GFP and reinstert a GFP+RhlI operon.
Same has to be done for incorporating RhlI in the GFP operon on the pHD plasmids. We may use PciI to cut the plasmid in one location: 3382. But we have to check if we were the terminator is. May have to digest out the GFP and reinstert a GFP+RhlI operon.
 +
 +
==Digestion for biobrick assembly :==
 +
 +
===We started at both ends so that if there is a problem, we still advance somehow.===
 +
- LuxI(F1610) and RFP(E1010)
 +
<p>
 +
- constitutive promoter(I14033) and RhlR(I1466)
 +
===We assemble some small bricks together to gain time===
 +
- ptetR(R0040) and RBS(B0034)
 +
 +
- PRhlR(R0071) and RBS(B0034)
 +
 +
==PDMS device finishing==
 +
 +
The first batch of 4 microfluidics devices was almost finished. Yesterday, following the protocol on the main page of the "notebook", the two layers (control and flow) were molded on the wafer molds constructed in the clean room last week. They were aligned and baked for 1h30. Today, they were cut off from the mold and trimmed around the edges. They were left to bake overnight at 80°C following the protocol.

Latest revision as of 12:12, 7 August 2008

<<Previous - Back to Notebook - Next>>

Contents

2 Step PCR Protocol

We started a 2 step PCR too get LuxR, lasR, RhlR genes. We intend to convert them to proteins invitro to test their binding affinity to their DNA sites. 1st step worked except for LasR, but we were not sure the gene was actually in the plasmid. 2nd stop should finish this evening. We have to order the "ribosomal solution" to continue. We used more DNA and primers because 1st try didn't work. Here is our protocal. Normaly 1ul of DNA and primers.

1st Step

dNTP
1ul
10x Buffer + mgcl2
5ul
DNApoly
1ul
3'primer
5ul
5'primer
5ul
template
5ul
H2O
28ul
---------------------
----------
Total
50

2nd Step

Dilute primers to 250nM each. The template is the previous PCR mix

dNTP
1ul
10x Buffer + mgcl2
5ul
DNApoly
1ul
Primer mix
1ul
template
5ul
H2O
41.5ul
---------------------
----------
Total
50

Launch for 10 cycles and then add the final primers. 1ul of each and launch for an other 30 cycles.

We our finishing the exaxt design of our plasmids. Extracting LacI from the Ron-Weiss plasmid and making it a part will probably need new primers(so we can add the restriction sites).

Same has to be done for incorporating RhlI in the GFP operon on the pHD plasmids. We may use PciI to cut the plasmid in one location: 3382. But we have to check if we were the terminator is. May have to digest out the GFP and reinstert a GFP+RhlI operon.

Digestion for biobrick assembly :

We started at both ends so that if there is a problem, we still advance somehow.

- LuxI(F1610) and RFP(E1010)

- constitutive promoter(I14033) and RhlR(I1466)

We assemble some small bricks together to gain time

- ptetR(R0040) and RBS(B0034)

- PRhlR(R0071) and RBS(B0034)

PDMS device finishing

The first batch of 4 microfluidics devices was almost finished. Yesterday, following the protocol on the main page of the "notebook", the two layers (control and flow) were molded on the wafer molds constructed in the clean room last week. They were aligned and baked for 1h30. Today, they were cut off from the mold and trimmed around the edges. They were left to bake overnight at 80°C following the protocol.