"
Team:University of Lethbridge/Notebook/Project1July
From 2008.igem.org
Contents |
July 1, 2008
Nathan Puhl
Subcultured RP1616 into liquid LB and pTopp cells into liquid LB + amp
July 2, 2008
Nathan Puhl, Christa, Munima
Plasmid mini prepped pTopp cells.
Attempted to make RP1616 cells competent using the open wet ware [http://openwetware.org/wiki/Preparing_chemically_competent_cells protocol]. 100 uL aliquots of cells were frozen in liquid nitrogen and stored in the -80 freezer.
Ran CheZ in pUC19 plasmid and pUC19 plasmid from last year with high range ladder. The pUC19 plasmid seems weird, I don't think it should have two bands; I will have to ask someone about that. The CheZ plasmid appears to be the right size (2600 + 620 = 3220 bp)
July 3, 2008
Nathan Puhl, Munima, Christa
No colonies on either plate, but the max-efficiency DH5-alpha cells transformed with pSB1A7 were successfully transformed (~1500 cfu). There are two possibilities: 1. the cells are competent but are low efficiency and we did not add enough DNA, or 2. The cells are not competent. To assess possibility one we will try more DNA. If that does not work we will try a protocol using electroporation.
July 8, 2008
Munima, Christa
Objective: Attempt to transform pSB1A7 into RP1616 cells (made competent on July 2/08) again, but using more DNA and changes to June 16/08 transformation protocol
1. Thawed RP1616 cells and pSB1A7 on ice (obtained from Wieden -80 C freezer) 2. Added 50uL of RP1616 cells to a 15mL falcon tube (prechilled) 3. Left on ice for 10 minutes 4. Added 4uL of pSB1A7 to falcon tube 5. Incubated on ice for 30 minutes 6. Heat shocked without shaking for 45 seconds at 42 C 7. Placed on ice for 2 minutes 8. Added 1mL of SOC media preheated to 42 C. Incubated for 1 hour at 37 C in shaker incubator 9. Put a 400uL aliquot of mixture from incubator into a centrifuge tube 10. Centrifuged for 1 minute on max speed 11. Poured off supernatant and resuspended in 100uL of SOC media 12. Plated 100uL on LB + amp plate. Left overnight in incubator.
July 9, 2008
Munima, Christa
Growth observed on amp plate that was plated with transformed competent RP1616 cells with pSB1A7. Approximately 10 colonies were observed, but they look strange.
Subcultured one colony into 5mL LB + amp culture tube (50ug/mL ampicillin). Left overnight in shaker incubator at 37 C at 225 RPM.
July 10, 2008
Munima, Christa
Did plasmid mini prep on RP1616 competent cells with pSB1A7 from the culture tube left overnight. Eppendorf FastPlasmid mini kit was used and the tube was stored in the -20 C iGEM freezer labelled "comp RP1616 + pSB1A7".
July 15, 2008
Munima, Christa
Objective: Make RP1616 cells competent via electroporation
Inoculated two 5 mL culture tubes with RP1616. Left overnight in shaker incubator at 37 C. Inoculations will be used for electroporation on July 16, 2008
July 16, 2008
Christa
Objective for today: Attempt to use electroporation to transform pTopp or pSB1A7 into RP1616 cells.
Made a 1/5 dilution of cells in culture tubes. Left dilution in shaker incubator at 37 C (300RPM) for approximately 4 hours.
Christa, Munima, Selina
Machine: Eppendorf Electroporator 2510
Plasmids pSB1A7 and pTopp will be used.
1. Spun down 2.0 mL of cell culture in two transfers (first added 1.5 mL, removed supernatant, then added another 0.5 mL of culture) into 1.5 mL centrifuge tubes. (Four centrifuge tubes in total) 2. Poured off supernatant. Resuspended in 1 mL of ice cold water to wash (2x). 3. Resuspended in 100 uL of 10% glycerol in water. 4. Added 2 uL of plasmid. Sat for 10 min on ice. (Two tubes for each plasmid) 5. Poured mixture into prechilled 0.1 cm cuvette. 6. Electroporated with 1.5 kV for 2.4 msec. 7. Immediately added 1 mL of media. Three of four tubes were spun down and resuspended. All were in SOC media at completion. 8. Transferred to 15 mL Falcon tube. 9. Left on shaker incubator at 300 RPM and 37 C for approx. 1.5 hours
Munima
10. Took 400 uL aliquots of culture and centrifuged at max for 1 min. 11. Poured off supernatant and resuspended in 100 uL of SOC media. 12. Plated 100uL on LB + amp plates. 13. Left to incubate overnight at 37 C.
July 17, 2008
Selina
Checked LB + Amp plates of electroporated RP1616 cells 16 hours later (next morning). Plates showed thick growth (no isolated colonies) in localized swirly patterns
- yesterday cell-media culture was plated by swirling plate on benchtop and growth possibly reflects that - if so, then very likely the electroporation/transformation was sucessful :) - possible problem of satellite colonies? amp may have been used up with such thick growth... - wrapped plates in parafilm and placed in 4 C fridge for storage - future plans: use plate to inoculate culture tubes with amp and attempt to replate for isolates (once more plates are poured...
Plated other half (less than 500 uL) of cell-SOC media culture on LB + Amp plates.
- Cultures were sitting at RT overnight and likely have entered death phase... - Took cell cultures, transferred to microcentrifuge tubes, spun and resuspended in 100 uL LB. - Spread-plated cell cultures (4 total, 2 per attempted plasmid transformation) on LB + Amp plates. - Left to incubate (at ~8:15 am) at 37 C. - note for future attempts: if this comes up again, then try replenishing liquid media in old cell culture - try to revive/awaken any dormant cells..? ask an actual microbiologist what would be smarter to do
Christa
Streaked colonies of pSB1A7 and pTopp onto Brent's LB + amp plates because there was too much growth on the plates observed on the plates today.
July 18, 2008
Sebastian, Munima, Christa, Selina
Observed very small colonies on streak plates (LB + amp) of pSB1A7 and pTopp (RP1616).
