"
Team:Tokyo Tech/Acrylic container
From 2008.igem.org
(Difference between revisions)
| (23 intermediate revisions not shown) | |||
| Line 8: | Line 8: | ||
!align="center"|[[Team:Tokyo_Tech/Result|Result]] | !align="center"|[[Team:Tokyo_Tech/Result|Result]] | ||
!align="center"|[[Team:Tokyo_Tech/Team|The Team]] | !align="center"|[[Team:Tokyo_Tech/Team|The Team]] | ||
| - | !align="center"|[[Team:Tokyo_Tech/ | + | !align="center"|[[Team:Tokyo_Tech/Acknowledgements|Acknowledgements]] |
|} | |} | ||
| Line 15: | Line 15: | ||
| - | == ''' | + | == '''Acrylic container''' == |
<html> | <html> | ||
<body> | <body> | ||
| Line 38: | Line 38: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| - | < | + | <p> </p> |
| + | <p> </p> | ||
| + | |||
<table width="100%" border="0" cellspacing="0" cellpadding="0"> | <table width="100%" border="0" cellspacing="0" cellpadding="0"> | ||
<tr> | <tr> | ||
| Line 50: | Line 52: | ||
<table width="100%" border="0" cellspacing="0" cellpadding="0"> | <table width="100%" border="0" cellspacing="0" cellpadding="0"> | ||
<tr> | <tr> | ||
| - | <td class="a" width="2%"> <IMG src="https://static.igem.org/mediawiki/2008/ | + | <td class="a" width="10%"> </td> |
| + | <td class="a" width="2%"> <IMG src="https://static.igem.org/mediawiki/2008/a/a5/Tech_aqulyl1.jpg | ||
" align="middle"></td> | " align="middle"></td> | ||
<td class="a"> | <td class="a"> | ||
| - | <p class=MsoNormal>* | + | <p class=MsoNormal>* “Ptet” on pSB6 plasmid (E.coli strain; JM109)</i></p></td> |
| - | + | ||
| - | + | ||
</tr> | </tr> | ||
</table> | </table> | ||
| - | < | + | <p> </p><p> </p> |
<table width="100%" border="0" cellspacing="0" cellpadding="0"> | <table width="100%" border="0" cellspacing="0" cellpadding="0"> | ||
<tr> | <tr> | ||
| Line 70: | Line 71: | ||
<table width="100%" border="0" cellspacing="0" cellpadding="0"> | <table width="100%" border="0" cellspacing="0" cellpadding="0"> | ||
<tr> | <tr> | ||
| - | <td class="a" width=" | + | <td class="a" width="10%"> </td> |
| - | <td class="a" width=" | + | <td class="a" width="40%"> |
<IMG src="https://static.igem.org/mediawiki/2008/a/af/Tech_acrylic1.JPG | <IMG src="https://static.igem.org/mediawiki/2008/a/af/Tech_acrylic1.JPG | ||
| - | " align="middle"></td> | + | " align="middle" width="300"></td> |
<td class="a" width="40%"><IMG src="https://static.igem.org/mediawiki/2008/0/01/Tech_acrylic2.JPG | <td class="a" width="40%"><IMG src="https://static.igem.org/mediawiki/2008/0/01/Tech_acrylic2.JPG | ||
| - | " align="middle"></td> | + | " align="middle" width="300"></td> |
</table> | </table> | ||
| - | | + | <a> </a> |
| + | <a> </a> | ||
| + | <a> </a> | ||
</div> | </div> | ||
</body> | </body> | ||
</html> | </html> | ||
| - | |||
Latest revision as of 11:22, 26 October 2008
| Home | Construction | Acrylic container | Development of promoter | Genetic toggle switch | Parts Submitted to the Registry | Result | The Team | Acknowledgements |
|---|
Acrylic container
 |
|
We create devices for confirming pressure response of lac promoter. This is the first step of creating touch display. This device made of Acrylic glasses and has two holes (show figure). Each hole contains tubes and water. Inside tubes E. coli is cultivated. Pressure can travel to inside tubes. One hole (A) is covered with a plastic tape (show figure). Therefore the hole is pressurized.The other (B) is covered with a block made of an acrylic glass. (show figure) Therefore the hole is not pressurized by water. |
|
E.coli type in tubes |
 |
* “Ptet” on pSB6 plasmid (E.coli strain; JM109) |
|
After pressurized the container, we observed the E.coli by a fluorescence microscope. The result shows below. |
 |
 |
