"
Team:Tokyo Tech/Construction
From 2008.igem.org
| (One intermediate revision not shown) | |||
| Line 32: | Line 32: | ||
| - | + | {{clear}} | |
| - | + | ||
| - | + | ||
| - | + | ||
'''Experiment under high pressure''' | '''Experiment under high pressure''' | ||
| Line 41: | Line 38: | ||
Finally, pressurize pressure vessel by pressure device(figure5). and then incubation was started at 37℃ immediately at each pressure vessel(original designed) for 16h at 37℃.After cultivation(figure6), the cells were examined by fluorescence microscope. | Finally, pressurize pressure vessel by pressure device(figure5). and then incubation was started at 37℃ immediately at each pressure vessel(original designed) for 16h at 37℃.After cultivation(figure6), the cells were examined by fluorescence microscope. | ||
| - | <gallery widths = " | + | <gallery widths = "150px" heights="150px" perrow="4" align="center" > |
| + | Image:Tech_tube_2.JPG|figure3 Polypropylene tubes with parafilm | ||
Image:Tech_equip1.jpg|figure4 Pressure vessel | Image:Tech_equip1.jpg|figure4 Pressure vessel | ||
Image:Tech_equip2.jpg||figure5 Pressure device | Image:Tech_equip2.jpg||figure5 Pressure device | ||
| Line 47: | Line 45: | ||
</gallery> | </gallery> | ||
| - | + | {{clear}} | |
| - | + | ||
| - | + | ||
| - | + | ||
[[Image:Pressure-response_ability_of_PtetR.png|350px|thumb|right|figure2 Result of experiment]] | [[Image:Pressure-response_ability_of_PtetR.png|350px|thumb|right|figure2 Result of experiment]] | ||
| - | |||
'''Result''' | '''Result''' | ||
The result was that PtetR activity under 30MPa pressure is about 2.5 times stronger than PtetR activity under 0.1MPa pressure. Therefore, we confirmed that PtetR was induced under 30MPa pressure. | The result was that PtetR activity under 30MPa pressure is about 2.5 times stronger than PtetR activity under 0.1MPa pressure. Therefore, we confirmed that PtetR was induced under 30MPa pressure. | ||
Latest revision as of 13:04, 26 October 2008
| Home | Construction | Acrylic container | Development of promoter | Genetic toggle switch | Parts Submitted to the Registry | Result | The Team | Acknowledgements |
|---|
Confirmatory experiment
Construction
For confirming pressure-response ability of pressure-inducible promoter, we experimented under 0.1MPa and 30MPa pressure. We chose TetR promoter(PtetR) as pressure-inducible promoter and we constructed two plasmids - one is PtetR-GFP on pSB6([http://partsregistry.org/Part:BBa_K121010 BBa_K121010]), the other is promoter less-GFP on pSB6([http://partsregistry.org/Part:BBa_K121013 BBa_K121013]) as a negative control.
Experiment under high pressure
Dilute this culture medium by 1% by adding fresh medium and suitable antibiotic (ampicilin; 50㎍/ml). Next, seal this culture medium with oxygen-saturated fluorinert (25% volume of medium) in polypropylene tubes with parafilm (figure3). Put this tube into pressure vessel filled with water (figure4). Next cup pressure vessel. Finally, pressurize pressure vessel by pressure device(figure5). and then incubation was started at 37℃ immediately at each pressure vessel(original designed) for 16h at 37℃.After cultivation(figure6), the cells were examined by fluorescence microscope.
 figure3 Polypropylene tubes with parafilm |
 figure4 Pressure vessel |
 |figure5 Pressure device |
 figure6 Constant-temperature bath |
Result
The result was that PtetR activity under 30MPa pressure is about 2.5 times stronger than PtetR activity under 0.1MPa pressure. Therefore, we confirmed that PtetR was induced under 30MPa pressure.
