Team:Hawaii/Initial Synth. Oligo Assembly

From 2008.igem.org

Revision as of 20:46, 8 July 2008

Protocol

Hybridization of Parts

1. Mix:

   3 μl 100 µM sense oligo

   3 μl 100 µM anti-sense oligo

   3 μl 10 x PNK (polynucleotide kinase) buffer

   2 μl 10mM ATP

   2 μl T4 polynucleotide kinase (PNK)

   17 μl distilled water

   Total volume = 30 μl

2. Incubate at 37C for 1.5 hours.
3. Add 4 μl 0.5 M NaCl.
4. Place in boiling water bath for 2 min., then remove water bath from the heat source and allow the reaction (still in the water bath) to cool to room temperature (approx. 30 minutes)

Reference: Pam Silver Lab. [http://openwetware.org/wiki/Silver:_Oligonucleotide_Inserts| Oligonucleotide Inserts.]

DNA Ligation

1. Combine 4 ul of construct one with 4 ul of construct 2.
2. Add 1 ul of nanopure H₂0.
3. Add 10 ul of 2x quick ligation reaction Buffer. In order to avoid shearing the DNA, mix by resuspending very slowly.
4. Add 1 ul of Quick T4 DNA ligase and mix thoroughly by resuspending very slowly.
5. Incubate at room temperature for 5 minutes.
6. Cool on ice then transform, or store at -20^oC

Reference: Quick Ligation Kit from NEB.

Restriction Enzyme Digest

• May not be necessary

1. Add REs in appropriate amounts to appropriate buffer (check if enzymes are compatible).
2. Incubate 1 hour at recommended temperature (usually 37C).
3. Stop reaction by adding 5 μl 10X loading buffer or by incubating 10 min. at 65C.

Notes:

• <10% of digest should be RE
• REs are stored in glycerol. <5% glycerol should be present in digest. Therefore, a minimum 10-fold dilution is necessary so the enzymes don't act funky.
• It's always a good idea to gently shake and spin down RE and RE buffer prior to use.

Reference: Short Protocols in Molecular Biology. Vol. 1. 5th edition. 3-3 to 3-4.

Results

First attempt

Nice bands observed for annealed oligos. Bands appear to be the correct size (<100bp) but we can't tell if anneal worked (EtBr doesn't tell us if these are ssDNA or dsDNA bands). Smear is probably from loading way too much DNA (see discussion). Possible faint band for pnir ligation. No bands for slr2016 and pilA ligation, probably because way too much DNA was added for the ligation reaction.

Second attempt

Did a ligation using 1 μl of a 10^-6 dilution of each annealed product. Nothing was visible on the EtBr stained 4% agarose gel because not enough DNA was present.

Third attempt

Did a ligation using 10^-2 dilutions of annealed product. Faint bands were visible for the annealed products (10^-2 dilutions) but no bands were observed for the ligated products. Not enough DNA was present. Ran 10^-1 dilutions of annealed product on SYBR Safe stained 2% agarose gel.

Fourth attempt

Took 10 μl ligation reaction from first attempt and restriction digested with XbaI and PstI (1 μl each) in NEBuffer 3 (1 μl). A ladder of bands were observed for the ligation product, indicating incomplete digestion.

First assembly attempt. Ten microliters loaded into each well of an EtBr stained ~3% agarose gel ran at 95V for 1 hr.

Third ligation attempt. Ten microliters loaded into each well of an EtBr stained 4% agarose gel ran at 95V for 28 min.

SYBR Safe stained 2% agarose gel ran at 95V for 30 min. Ten microliters of a 10^-1 dilution of annealed product was loaded into each well.

Fourth attempt. Ten microliters of 10^-1 dilution of annealed product or 1:1 ligation product was loaded into each well. Ran on EtBr stained 4% agarose gel at 95V for 30 min.

Discussion

We need to dilute our annealed products before running them in a gel or attempting ligation. 20-125ng DNA (per lane) is good for running gels. One reaction using the NEB Quick Ligation Kit can ligate up to 180ng of DNA.

• Recent changes
• What links here
• Related changes
• Special pages
• My preferences

• Printable version
• Permanent link
• Privacy policy
• Disclaimers