From 2008.igem.org

Revision as of 13:31, 29 October 2008

Visualization - Methods revealed
back to the visualization notebook

Microscope

Was performed using LabtekTM chambered coverglass systems (Nunc). In most analysises mainly two versions were used.

Small chamber 2x4 wells

Large chamber

All those samples were monitored using an Applied Precision - DeltaVision confocal microscope. After the first experiments have been finished, further experiments were only performed with fluorescent strains. They are much more accurate and may be used for quantified analysis methods.

Usual transmission

Merged picture

Fluorescent shot

back up

Frames

Sample of a frame used for small chambers

Draw of two frames on a large chamber, Each frame is covering one half of the chamber

To analyse chamber samples in several time steps (e.g. after 3,6,9 hours ...)
under the microscope a system was needed, limiting the amount of data and making an analysis possible. Therefore several frames have been developed, which cover the chamber as good as possible and allows the best estimation about the events of the experiment.

On the right side is one example for each type of chamber:

Every black spot stands for a taken picture at this position.
These draws are just examples of potential frames.

For small chambers square frames were used like 10x10 or 8x8 meaning 100 or 64 pictures at the end. To cover enough space of large chambers two separate frames had to be used. Each of those frames was usually about 6x8 (6 in heigh and 8 in length) fields.

back up

chemotactical activity

This test serie was used test the chemotactical activity of strains depending on special strain abilities and the media they were incubated in or transferred to. 3 µl of an overnight culture were put into a small chamber filled with 200 µl of the appropriate media.
The status of the bacteria has been observed over several hours. Depending on the experiment sometimes after a specific time an attractant like casamino acids have been added to the media to test the effect of the attractant on the activity of the specific strain.

This was performed with short time lapse series like taking 90 pictures at one position with a time lapse of less than 0.33 seconds.

This experiment may give an idea of the behavior of certain strains under specific conditions.
With this information it is more easy to choose the right strain and the best conditions for further experiments.
It is also possible to predict the bacterial behavior, so that some parameters can be excluded if the bacteria do not act as expected.

Here is one example of such a time lapse serie:
To see this video the quicktime plugin for the appropriate browser is needed.

back up

computer-assisted analysis

ImageJ

The Deltavision confocal microscope gives usually Deltavision files (.dv) as output, which are not easy to handle and may also be in stacks or somehow or not colored as wanted. It is much more easy to work with Jpeg files and proccess the images during the coonversion. But the amount of images is to high to convert image per image.
Therefore homemade plugins for ImageJ were used to convert those files to Jpeg files and if needed processes them. (For example by coloring and/or merging.)

Furthermore for the automatic processing a [http://www.loci.wisc.edu/ome/formats-imagej.html LOCI Bio-Formats] importer plugin was used. The link can be found by clicking on the name.
This plugin enables the automatic processing of Deltavision files in ImageJ.

An example for such a plugin would be:

Just click on the picture above to see the plugin.

The plugin *.txt has to be in the macros folder which is located in the ImageJ mainfolder, then the plugin can be run from windows with the following command in the commandline:
java -jar ij.jar -batch nameoftheplugin

This plugin takes a serie of 64 pictures taken with the Deltavision microscope in the specific folder.
Each file was a stack of 2 pictures with to different channels. The plugin opens the files merges them to one RGB picture, converts them to Jpeg and saves the new pictures in the same folder.

Those grey pictures are 2 pictures forming one stack, the third one is the product of the plugin:

Analysis with MatLab

Furthermore every picture can be correlated with an intensity value.
In combination with an automatic picture arrangement function, which many image processing programs provide this allows to create 3D graphics, which can be compared with their frame pictures.
To see some results of this image processing and analysis: ~~click here~~


An example of analysing the left frame of an experiment with the large chamber:

Just click on the picture above to see the code.

There are several other possibilities to change the calculation operation of the parameters and adjust the 3D graphic.

This can be combined with analysing the right frame as well.
If the result like here would be A=feld and if the result of the right frame is B=feld both frames can be combined and shown as a 3D grapic with the following commands:

C=[A,B]
surf(C')
shading interp

Examples of this can be seen on the click here link above.

back up

Swarm Assays

PROTOCOL FOR SWARM-PLATE CHEMOTAXIS AGAINST A POSSIBLE ATTRACTANT:
This protocol was created using petri-dishes. But every other chamber could be used as well.

• Step 1: Make sure you have everything ready to get started. You need:
  • Petri-dishes. !!! sign your petri-dishes before You pour in the media. Also mark the spots where you want to set the attractant or attractant line and the bacteria. !!! Handle the soft agar with care. After the addition of the attractant the petri-dish should only be moved really carefully.
  • 50 ml falcons
  • 25 ml media containig 0.2%-0.3% Agar for every petri-dish.
  • samples of the appropriate attractants. The concentration depends on several substance depending attributes.
  • Other substances like antibiotics (Amp, Kan, Cm) or inducer (IPTG, Arabinose)
• Step 2: Your agar-media solution should be clear and the agar completely dissolved. If you want to use attractant plugs¹ or other non fluid attractants, go first through step 5 then back through 2,3,4 skip 5, further with 6 and so on...
• Step 3: Take Take a 50 ml falcon pour 25 ml of your agar containing media in it and add antibiotics or inducing substances. If no extra substances are needed just skip this step.
• Step 4: Let your media polimerize. At least let it rest for 15/20 min.
• Step 5: Then add the attractant. e.g.: a casamino acid solution
• Step 6:
  • Put the whole plate into a 4°C fridge for 12-16 hours to allow the attractant to build up a gradient.
  • Make an overnight culture of the strains you want to test, use TB media and add inducing substances if something has to be induced.

Next day:

• Step 7: Take your overnight culture. It should be at an OD of 0.4-0.6. Then take 1 ml of the bacteria suspension and centrifuge it for 10 minutes at 4,000 rpm. Resolve the pellet at 100 µl of the media you are using in the petri-dish.
• Step 8: Place 3-6 µl of your purrified bacteria at the premarked spots on the petri-dish sample.
• Step 9: Put the whole plate into the incubator at ~30°C and take a look at your plates after 24, 48 and 72 hours. Put the plates into a plastic bag like the small ones for the bench trash to protect the plates from running dry to fast. Only move the plates if necessary.

¹: Attractant plugs can be created by adding agar to the attractant solution.

Center attractant plug line

Spotted attractants

Center fluid attractant line

This picture is showing an alternative chamber

back up

back to the visualization notebook

• Recent changes
• What links here
• Related changes
• Special pages
• My preferences

• Printable version
• Permanent link
• Privacy policy
• Disclaimers