Team:KULeuven/7 September 2008

From 2008.igem.org

• Home
• Reports
• Calendar

• Project abstract
• Meet the team
• Leave a message
• Mail us

• The Team
  Research Labs and Groups Students Instructors Advisors Pictures
• The Project
  Summary Components

  Input Output Filter InverTimer Reset Cell Death Memory

  Safety End Evaluation Literature Brainstorm
• Ethics
  Introduction Three A's

  Defining the three A's Developments in modern physics Developments in biology

  Concerns & Issues

  Defining synthetic biology A framework Concerns Issues The need for answers

  Biological Robotics

  KULeuven iGEM 2008 project Biological robotics

  Afterword References
• Submitted Parts
  Sandbox
• Modeling
  Overview Kinetic Constants Components

  Output Filter InverTimer Reset Cell Death Memory

  Full Model Sensitivity Analysis Multi-cell Model Diffusion
• Data Analysis
  Overview New Parts

  GFP (LVA-tag) Other

  Components

  Input Output Other
• Software
  Multi-cell Toolbox Simbiology2LaTeX Toolbox
• Notebook
  Protocols Reports

  Daily Weekly

  Lab Data

  Freezer Primers Ligation

  Tools Press Acknowledgments

Lab Work

Wet Lab

Another day, another lab report:

• We did a PCR of the hybrid promoter with the prefix-suffix primers. This gave about the same results as yesterday, albeit a bit better. Maybe because we annealed at a higher temperature this time. Anyhow, we still saw a bit of laddering which we presume to be caused by concatenation of the prefix-suffix primer into constructs like (- Prefix - Promoter - Suffix - )_X. We cut out the (quite broad) band at the right length and extracted the DNA. We hope that by digesting, we once again get the decent cut-out part.
• We made a gel with the PCR samples of the ligation test and with the digests (K145201, K145205, K145253, K145251 and R0040+J23022+J23109+J23032). The result was very good, we now have a lot of new BioBricks that are finished. Only R0040+J23022+J23109+J23032 gave bad results. Both the PCR and the digest was too short. This is the second time that this ligations fails. We think the problem lies in the first part (R0040+J23022). We will not use this one anymore. We wil use R0040+J23066 instead. This ligation definitely succeeded and this part contains key3d and is compatible with the old lock (J23032).
• Yet another failure: PCR of T7 polymerase with UmuD tag failed again (surprise!). We followed the protocol that gave us 3 bands earlier but this time we did only 2 annealing steps at 56 degrees in stead of 3. The third step was replaced by one at 62 followed by 32 at 68 degrees.
• We also found out that the part R1052 doesn't contain a prefix or suffix. That's why the digest and PCR didn't work. We will make some oligos to construct it ourself.
• We electroporated the following parts: K145150+pSB1A2, K145150+E0240, K145150+B0034, K145013+pSB1A2, R0040+P0353, E0040+B0015, B0014+B0033+C0061+B0015 and K145254.
• Set up some ligations: K145201+K145205, K145201+(R0040+E0240), (R0040+B0033)+(C0056+B0015), (R0040+J23066)+(J23109+J23032), (J23109+J23032)+(K145001+B0015) and (J23116+B0032)+(C0062+B0015).

So, we now have a few new BioBricks. A list of all the BioBricks that should be finished by the end of this month (including those needed for tests and intermediates), can be found here. You can also see which ones have succeeded so far.

Dry Lab

Designed 2 oligos to construct R0052 (replacing R1052) ourselves. Will enter them as soon as possible.

Modeling

Wiki

Remarks

Comic of the day

• Recent changes
• What links here
• Related changes
• Special pages
• My preferences

• Printable version
• Permanent link
• Privacy policy
• Disclaimers