Team:Harvard/Dailybook/Week1/Widgetry

From 2008.igem.org

(Difference between revisions)
(New page: =Monday: June 23, 2008= ==Lab== * Received ordered parts from McMaster-Carr * Drew preliminary designs for MFC 300px * Cut polycarbonate tubing ** 2" Square T...)
 
Line 3: Line 3:
* Received ordered parts from McMaster-Carr
* Received ordered parts from McMaster-Carr
* Drew preliminary designs for MFC  
* Drew preliminary designs for MFC  
-
[[Image:Mfc_prototype1.jpg|300px]]
+
[[Image:800px-Mfc_prototype1.jpg|300px]]
* Cut polycarbonate tubing
* Cut polycarbonate tubing
** 2" Square Tubing:
** 2" Square Tubing:
Line 14: Line 14:
* Tested 5 minute epoxy:
* Tested 5 minute epoxy:
** Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet
** Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet
-
[[Image:Mfc_epoxy.JPG|300px]]
+
[[Image:800px-Mfc_epoxy.JPG|300px]]
* Tested silicon:
* Tested silicon:
** Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet
** Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet
-
[[Image:Mfc_silicon.JPG|300px]]
+
[[Image:800px-Mfc_silicon.JPG|300px]]
* Tested silver epoxy:
* Tested silver epoxy:
** Attached titanium wire to graphite sheet
** Attached titanium wire to graphite sheet
-
[[Image:Mfc_silverepoxy.JPG|300px]]
+
[[Image:800px-Mfc_silverepoxy.JPG|300px]]
==Results==
==Results==
Line 75: Line 75:
*Milled holes for injection ports and bolts
*Milled holes for injection ports and bolts
*Assembled prototype for MFC minus anode and membrane
*Assembled prototype for MFC minus anode and membrane
-
[[Image:Mfc_prototype2.JPG|300px]]
+
[[Image:800px-Mfc_prototype2.JPG|300px]]
*Make cathode using alternative wiring design to maximize surface area
*Make cathode using alternative wiring design to maximize surface area
*Made another chamber using epoxy for autoclave test
*Made another chamber using epoxy for autoclave test
*Airtight test by submerging pressurized MFC prototype in water
*Airtight test by submerging pressurized MFC prototype in water
** No air bubbles observed  
** No air bubbles observed  
-
[[Image:Mfc_oxygentest.JPG|300px]]
+
[[Image:800px-Mfc_oxygentest.JPG|300px]]
==Purchased==
==Purchased==
Line 142: Line 142:
**added nafion membrane
**added nafion membrane
**added carbon felt anode
**added carbon felt anode
-
[[Image:Mfc_prototype3.JPG|300px]]
+
[[Image:800px-Mfc_prototype3.JPG|300px]]
*membrane did not pass water-tight test
*membrane did not pass water-tight test
Line 150: Line 150:
'''''Warped membrane'''''
'''''Warped membrane'''''
-
[[Image:Mfc_nafionwarped.JPG|300px]]
+
[[Image:800px-Mfc_nafionwarped.JPG|300px]]
'''''Normal membrane'''''
'''''Normal membrane'''''
-
[[Image:Mfc_nafionnormal.JPG|300px]]
+
[[Image:800px-Mfc_nafionnormal.JPG|300px]]
* new MFC:
* new MFC:
Line 167: Line 167:
***outer “ring”
***outer “ring”
***cathode chamber
***cathode chamber
-
[[Image:Mfc_prototype4.JPG|300px]]
+
[[Image:800px-Mfc_prototype4.JPG|300px]]
:* water tight test:
:* water tight test:
:** passed water tight test
:** passed water tight test
Line 179: Line 179:
==Lab==
==Lab==
*Finished building air cathode MFC, minus injection ports
*Finished building air cathode MFC, minus injection ports
-
[[Image:Mfc_airprototype.JPG|300 px]]
+
[[Image:800px-Mfc_airprototype.JPG|300 px]]
*Autoclaved LML
*Autoclaved LML
=== Keithley test ===
=== Keithley test ===
-
[[Image:Mfc_circuit.JPG|300px]]
+
[[Image:800px-Mfc_circuit.JPG|300px]]
* Connected simple battery-resistor circuit to both 2700 alone and with 7700 switching module
* Connected simple battery-resistor circuit to both 2700 alone and with 7700 switching module
** Used 8.78 V source of 4M ohm resistance with 1% accuracy
** Used 8.78 V source of 4M ohm resistance with 1% accuracy

Latest revision as of 17:49, 28 October 2008

Contents

Monday: June 23, 2008

Lab

  • Received ordered parts from McMaster-Carr
  • Drew preliminary designs for MFC

800px-Mfc prototype1.jpg

  • Cut polycarbonate tubing
    • 2" Square Tubing:
      • Three 1.5" sections
      • Two 3" sections
    • 3" Round Tubing:
      • Four 2" sections
    • Polycarbonate sheets:
      • Four 3x3" squares
  • Tested 5 minute epoxy:
    • Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet

800px-Mfc epoxy.JPG

  • Tested silicon:
    • Attached 1.5" (2" Diameter) polycarbonate square tubing to sheet

800px-Mfc silicon.JPG

  • Tested silver epoxy:
    • Attached titanium wire to graphite sheet

800px-Mfc silverepoxy.JPG

Results

Silicon

  • questionable adhesiveness

Epoxy

  • fairly strong adhesiveness

Silver epoxy

Resistances:

  • Wire : 0.35 Ω / in
  • Graphite: 1 Ω / in
  • Across junction: 5 Ω / in


Purchased

From McMaster-Carr

Qty. Part
20ft High-Temperature Silicone Rubber Tubing Soft, 3/16" ID, 3/8" OD, 3/32" Wall, Blue
20ft High-Temperature Silicone Rubber Tubing Soft, 3/16" ID, 3/8" OD, 3/32" Wall, White
3
(packs of 10)
Aluminum Oxide Cloth Sanding Sheet 280 Grit, 9" X 11"
1 Bright Finish High-Speed Stl Spiral Point Tap 1/4"-28, H3 Pitch Diameter, 2 Flute
2
(packs of 10)
Plain Steel Fully Threaded Stud 1/4"-20 Thread, 6" Length
3
(packs of 25)
Zinc Alloy Wing Flange Nut 1/4"-20 Screw Size, 1" Wing Spread

Tuesday: June 24, 2008

Meeting with Peter Girguis

General Design

  • Three basic designs:
    • Vertical with two chambers stacked
    • Vertical with anode and air cathode below
    • Horizontal (perhaps with incline)
  • Nitrogen/Oxygen bubbling
    • Maybe do in flasks outside of actual fuel cell

Lab

  • Milled holes for injection ports and bolts
  • Assembled prototype for MFC minus anode and membrane

800px-Mfc prototype2.JPG

  • Make cathode using alternative wiring design to maximize surface area
  • Made another chamber using epoxy for autoclave test
  • Airtight test by submerging pressurized MFC prototype in water
    • No air bubbles observed

800px-Mfc oxygentest.JPG

Purchased

From Alfa Aesar

Qty. Part
15x15cm Nafion® membrane, 0.180mm thick
10x10cm Carbon felt, 6.35mm (0.25in) thick, 99.0%

Wednesday: June 25, 2008

Lab

  • Autoclaved epoxy chamber
    • Results:
  • Laminated nafion membrane
  • Made two black silicone chambers
  • Tested MFC by bubbling air into anode chamber to test gas in/out ports
    • Result successful.
  • Wrapped carbon felt with titanium wire without epoxy
    • Resistance:
      • Across junction: 2.5 Ω
      • Felt: 1.5 Ω

Received from Peter Girguis:

  • Decade resistance box
  • Carbon fiber cloth


Purchased

From McMaster-Carr

Qty. Part
1
(packs of 10)
Inline Minature Air Regulator 1/4" Female Inlet, 1/4" Male Outlet, 5 Max SCFM
1
(packs of 10)
Brass Barbed Hose Fitting Barb X Male Pipe for 3/16" Hose ID, 1/4" Pipe
1
(packs of 10)
Brass Barbed Hose Fitting Barb X Female Pipe for 3/16" Hose ID, 1/4" Pipe
6 Polycarbonate Sheet 6" x 6" Sample, 1/4" Thick, Clear
2 Ft. Polycarbonate Square Tube 2" Square Tube
25 Ft. High-Temperature Silicone Rubber Tubing Soft, 3/32" ID, 7/32" OD, 1/16" Wall, Blue
25 Ft. High-Temperature Silicone Rubber Tubing Soft, 3/32" ID, 7/32" OD, 1/16" Wall, White

Thursday: June 26, 2008

Lab

  • finished building MFC
    • added nafion membrane
    • added carbon felt anode

800px-Mfc prototype3.JPG

  • membrane did not pass water-tight test
    • silicon sheet started bulging
    • nafion membrane started warping

Warped membrane

800px-Mfc nafionwarped.JPG

Normal membrane

800px-Mfc nafionnormal.JPG

  • new MFC:
    • design:
      • anode chamber
      • outer “ring”
      • polycarbonate with 15/36” hole
      • smaller ring
      • membrane
      • smaller ring
      • polycarbonate with 15/36” hole
      • outer “ring”
      • cathode chamber

800px-Mfc prototype4.JPG

  • water tight test:
    • passed water tight test
    • membrane still warps
  • made 1L of LML medium (for anaerobic Shewie growth) ( see recipe here)
    • pH was 3.5 initially
    • added NaOH until pH at 6.99
    • autoclaved

Friday: June 27, 2008

Lab

  • Finished building air cathode MFC, minus injection ports

800px-Mfc airprototype.JPG

  • Autoclaved LML

Keithley test

800px-Mfc circuit.JPG

  • Connected simple battery-resistor circuit to both 2700 alone and with 7700 switching module
    • Used 8.78 V source of 4M ohm resistance with 1% accuracy
      • Calculated current = 2.19 microamps
      • Measured current (from 2700) = 2.5 microamps
      • Measured current (from 7700) = 2.8 microamps

MFC test




1k ohms resistance

  • Bubbled nitrogen and oxygen into anode/cathode chambers.
  • 60mL LML medium and 15mL distilled water in anode chamber
  • 40mL of LML and 35mL distilled water in cathode chamber
  • Current began at around 21 microamperes, dropped fairly consistently before plateauing around 10 microamps after 50 minutes
  • Added small amounts of lactate, HEPE buffer, yeast extract, peptone in attempt to cancel out the current
    • saw sudden rise in current, but then decreased again.
    • no notable difference thereafter.

Switched to 10k resistance

  • dropped to about 4 microamps
  • very very very slow increase (about 4.1-4.3 microamps in 10 minutes)

Added shewie

  • initial increase to about 5.25 microamps
  • slow and steady increase to about 6.7 microamps

Switched back to 1k resistance

  • shot up to about 21 microamps
  • decreased to about 13.5 microamps after 10 minutes


Questions to answer

  1. What temperature were the fuel cells kept at? Do they need to be incubated at 30ºC?
  2. What type of shewie is ideal for anaerobic current production? How long should they have grown in liquid culture?
  3. What concentration of shewie should be added per 50 mL of medium? OD?
  4. How much current should be produced over 2 minute increments? Current production over time pattern.
  5. How much resistance should we be using?
  6. What should the voltage difference be? 6 volts?
  7. What is the best medium? Can we get away with our LML medium, or will we need to make the....extensive recipe?
  8. Why is there current production without shewie? Distilled water test?