USTC/Notebook/PCR&Colony PCR

From 2008.igem.org

(Difference between revisions)
 
(4 intermediate revisions not shown)
Line 1: Line 1:
-
<div id="header">{{Template:Team:USTC/Templates/Header}}</div>
 
-
 
'''[[Team:USTC/Notebook|< Back to Notebook]]'''
'''[[Team:USTC/Notebook|< Back to Notebook]]'''
Line 11: Line 9:
2. add the following components:
2. add the following components:
-
- 2µL PCR buffer (rock gently after thawing, quick spin before use)
+
*'''2µL '''  PCR buffer (rock gently after thawing, quick spin before use)
-
- 1.2uL  Mgcl2
+
*'''1.2uL''' MgCl<sub>2</sub>
-
- 0.4uL  dNTPs
+
*'''0.4uL''' dNTPs
-
- 200nM final concentration of each primer  
+
*'''200nM'''  final concentration of each primer VF2 and VR (0.2uL)
-
- 0.2uL Taq enzyme
+
*'''0.2uL'''  Taq enzyme  
-
- template DNA
+
*''template DNA''
-
(note: the total volume of PCR is 20µL)
+
(note: add ddH<sub>2</sub>O to 20µL, the total volume of PCR is 20µL)
3. make sure reaction tubes are properly capped before placing in thermocycler
3. make sure reaction tubes are properly capped before placing in thermocycler
Line 26: Line 24:
== colony PCR ==
== colony PCR ==
-
- 0.2 uL primer #1 (to 25uM)  
+
*'''0.2 uL''' primer #1 (to 25uM)  
-
- 0.2 uL primer #2
+
*'''0.2 uL''' primer #2
-
- 0.4 uL dNTPs  
+
*'''0.4 uL''' dNTPs  
-
- 2 uL Buffer  
+
*'''0.4 uL''' MgCl<sub>2</sub>
-
- 5 uL colony culture  
+
*'''2 uL''' PCR Buffer  
-
- 0.2 uL Taq  
+
*'''2 uL''' colony culture  
-
- 10.4 uL H20
+
*'''0.2 uL''' Taq enzyme
 +
*'''15.8 uL''' H<sub>2</sub>0
perform PCR with an initial heating step at 94C for 5 minutes followed by 25-35 cycles of 30sec at 94C, 30sec at 55C and 1Kb/min at 72C,and 72C for 10min
perform PCR with an initial heating step at 94C for 5 minutes followed by 25-35 cycles of 30sec at 94C, 30sec at 55C and 1Kb/min at 72C,and 72C for 10min

Latest revision as of 16:11, 27 October 2008

< Back to Notebook

PCR

Briefly, a typical reaction is set up as follows:


1. set up pre-labeled reaction tubes on ice

2. add the following components:

  • 2µL PCR buffer (rock gently after thawing, quick spin before use)
  • 1.2uL MgCl2
  • 0.4uL dNTPs
  • 200nM final concentration of each primer VF2 and VR (0.2uL)
  • 0.2uL Taq enzyme
  • template DNA

(note: add ddH2O to 20µL, the total volume of PCR is 20µL)

3. make sure reaction tubes are properly capped before placing in thermocycler

4. perform PCR with an initial heating step at 94C for 5 minutes followed by 25-35 cycles of 30sec at 94C, 30sec at 55C and 1Kb/min at 72C


colony PCR

  • 0.2 uL primer #1 (to 25uM)
  • 0.2 uL primer #2
  • 0.4 uL dNTPs
  • 0.4 uL MgCl2
  • 2 uL PCR Buffer
  • 2 uL colony culture
  • 0.2 uL Taq enzyme
  • 15.8 uL H20

perform PCR with an initial heating step at 94C for 5 minutes followed by 25-35 cycles of 30sec at 94C, 30sec at 55C and 1Kb/min at 72C,and 72C for 10min