Team:Illinois/Antibody Receptor Tyrosine Kinase Fusion Notebook

From 2008.igem.org

Revision as of 01:47, 8 October 2008 by Su4 (Talk | contribs)


Contents

July 1, 2008

Made Yeast Media

YPD Medium, per liter:

10g yeast extract

20g peptone

20g dextrose

20g agar(only for plates)

1. Dextrose filter sterilized, the rest autoclaved

2. Weigh nutrients into flask double the volume you want to make, and stir to dissolve

3. Dextrose added to autoclaved media to equivalent of 20 g/L

4. Liquid media placed on bench, plate media placed in 65 degree water bath approximately 5 minutes

5. Poured into plates and allowed to solidify


July 17, 2008

E.Coli Media

LB medium, per liter

10g tryptone

5g yeast extract

5g NaCl

1 mL 1N NaOH

15g (agar for plates)

1. Antibody DNA resuspended in TE buffer, 0.1 μg/μL

2. 5mL LB inoculated with single colony DH5a pro

3. Incubated at 37 degrees overnight


July 18, 2008

Competent cells:

1. 3mL overnight culture of DH5a pro

2. Inoculated into 35mL of LB

3. OD600 checked, want 0.2-0.3

4. Place culture on ice for 3 minutes

5. Spin at 10,000 rpm for 7 minutes, discard supernatant

6. Resuspend in 10 mL cold 30 mM CaCl2, incubated on ice overnight


July 19, 2008

Glycerol added to 10%, cells in freezer

Transformation:

1. Cells put in ice 30 min with 1μL plasmid(100ng)

2. Heat Shock for 2 minutes at 42 degrees

3. Ice for 8 minutes

4. Add cells to 1μL LB

5. Grow for 1 hour

6. Plate 100 to 200 μL on LB and amp, grow overnight


July 21, 2008

Observations:

Plenty of colonies on all plates

Also, making 5mL overnight cultures for mini-prep tomorrow.


July 22, 2008

Mini spin prep on LC and HC colonies

Place DNA in 100μL H2O in freezer


July 29, 2008

All primers brought to standard concentration, 30mM

33.3μL H2O added per n mole of primer


July 30, 2008

Assembly PCR: amplify antibody gene fragments and then assemble them, light and heavy chains

tube 1 2 3 4 5 6 7 8
Antibody chain H H L L H H L L
DNA source mini-prep synthesized IDT genes
template 0.5ul
primers 1ul of appropriate forward and reverse primer
MgCl2 3ul 5ul 3ul 5ul 3ul 5ul 3ul 5ul
master mix 20ul
H20 to 50ul total volume

Master mix already contains MgCl2; should have added extra to some tubes.

PCR program: 1. 94 degrees 5 min 2. 94 degrees 1 min 3. 50 degrees 1 min 4. 72 degrees 1 min 5. GOTO 2. 39 cycles 6. HOLD at 4 degrees

1.5% agarose gel made, 0.75g agarose in 50ml 0.5X TBE w/10ul EtBr.

20ul of PCR produts loaded on gel w/4ul 6X loading buffer, run at 200V for about half an hour.

All lanes had lots of DNA at ~375bp, PCR worked.

07-30-08 AbFrag Gel1.jpg


July 31, 2008

PCR to asemble fragments from yesterday.

tube 1 2 3 4
template from 7-30 PCR 2+3 2+7 6+7 1+8
template 0.5ul of both heavy and light chains
primers 1ul of appropriate forward and reverse primer
MgCl2 0ul 0ul 3ul 3ul
master mix 20ul
H20 to 50ul total volume

PCR program: 1. 94 degrees 5 min 2. 94 degrees 1 min 3. 50 degrees 1 min 4. 72 degrees 1 min 5. GOTO 2. 29 cycles 6. HOLD at 4 degrees

Products run on a 1.5% agarose gel, no products of 700-800bp.

7 31 08 assembly.jpg


August 1, 2008

PCR troubleshooting of yesterday's reaction: use gradient for annealing temp (40-65 degrees), use more template, leave out end primers

Four series of reactions using a gradient annealing temp were run in addition to a fifth series omitting the end primers.

reaction series A B C D E
template (5+7) from 7-30 PCR 0.5ul 1ul 1.5ul 2ul 1ul
primers 1ul of forward and reverse primers (omitted in E series)
master mix 20ul
H20 to 50ul total volume

annealing temps: 40, 43.8, 50, 54, 60, and 64 degrees

PCR program: 1. 94 degrees 5 min 2. 94 degrees 1 min 3. annealing step 1 min 4. 72 degrees 1 min 5. GOTO 2. 29 cycles 6. HOLD at 4 degrees

PCR products run on 1.5% agarose gel at 200V for ~20 minutes, then 240V for ~20 minutes.

Products in the 700-800bp range in all lanes. Perhaps it worked because of using a differnt product from the 7-30 PCR.

8 1 08 assembly gradient.jpg


August 6, 2008

1.5% agarose gel of 8-1 PCR products run to cut out bands. Products A1, B1, C1, and E1 used.

Bands around 800bp cut out for all lanes and invitrogen gel extraction kit used to collect DNA in 50ul H2O.


September 5, 2008

Flk-1 clones from [http://www.atcc.org/ATCCAdvancedCatalogSearch/ProductDetails/tabid/452/Default.aspx?ATCCNum=MGC-18600&Template=mgcMouseClones ATCC] streaked onto LB+amp and incubated at 37 degrees.


September 6, 2008

Colonies picked from flk-1 plate and inoculated into 5ml LB+amp, grown at 37 degrees.

Freeze-dried e. coli with YCp50-poly from [http://www.atcc.org/ATCCAdvancedCatalogSearch/ProductDetails/tabid/452/Default.aspx?ATCCNum=87555&Template=vectors ATCC] resuspended in 5ml LB, grown at 37 degrees.


September 7, 2008

Mini spin prep of flk-1 and YCp50-poly cells, plasmids stored in 50ul H2O.