Team:Paris/Modeling/BOB/Simulations page travail

From 2008.igem.org

(Difference between revisions)
(Understanding the dynamics)
(Understanding the dynamics)
Line 69: Line 69:
[[Image:Math1.jpg|center]]
[[Image:Math1.jpg|center]]
[[Image:Math2.jpg|center]]
[[Image:Math2.jpg|center]]
 +
 +
Then, we want to find the eigenvalues of the jacobian matrix, because they make us understand the behavior of the system. For example (since it is the case for our system), let us assume that we gave one real eigenvalue, and two imaginary ones. T
=== Using these elements to improve the system and give directions to the wet-lab ===
=== Using these elements to improve the system and give directions to the wet-lab ===

Revision as of 00:13, 7 October 2008

(Under Construction : synchronisation and whole system)

Simulations and Mathematical analysis


Contents

Oscillations

Short System

  • We wanted to see if, from a mathematical point of view, it was possible for the "short" system presented above to hover.
Oscillations1.jpg
  • Here are the equations we took into account :
FlhDC dynamics simul 3.jpg
FliA dynamics simul 3.jpg
TetR simul 3.jpg
  • The equations are normalized (thus the degradation term set to 1), as well as the parameters :
Parameters Used
Parameter Normalized Value
βFlhDC 1
θFlhDC 0.4545
n 2
βFliA 0.1429
β'FliA 0.8581
βLasI 0.2222
β'LasI 0.7778
  • As introduced before, the goal of this model was to give us useful bases on which to work on. Then, we shall use the values of the parameters presented below as a "starting point". We shall present a double approach, composed of a theoretical and a simulation approach. Both approaches should interact so as to help us understand the way our system behaves.
  • The obvious though process we propose consists in observing what happens with the simulation, then understand the source of these phenomenas. Finally, the ultimate goal consists in finding how we can pull the strings, hidden in the system, that control the behavior of the system.

Observations

---> petites oscillations + vérifier par le calcul ---> trop grande réactivité de flhDC

  • First of all, let us see what the simulation gives, and what pieces of information we can get from it.
  • Observation#1 :
    • By looking at this simulation, we could think that it is going to be hard to get oscillations...
      Simul fig1.jpg
    • However when we zoom, we get this more reassuring view :
      Simul fig2.jpg
    • Conclusion : some intrinsic oscillations actually occur, but they seem to be strongly attenuated. The mathematical study shall help us decide whether these are only artefact oscillations. For example we shall try to check if the period observed (~10 time units) can be linked to mathematical data.
  • Observation#2 :
    • Here, we need to change parameters a little bit, so that it becomes more obvious

Understanding the dynamics

  • The classical approach consists in finding the equilibrium state, by setting
Math0.jpg

Then, we evaluate the jacobian matrix, so as to put the system under its linearized form:

Math3.jpg
Math4.jpg

which gives :

Math1.jpg
Math2.jpg

Then, we want to find the eigenvalues of the jacobian matrix, because they make us understand the behavior of the system. For example (since it is the case for our system), let us assume that we gave one real eigenvalue, and two imaginary ones. T

Using these elements to improve the system and give directions to the wet-lab

Entire System

//biocham ici//+ comparaison avec le modele hillistique

FIFO

  • The goal here is to present the results of the simulations we made concerning the FIFO part of the system.

Here is the system we implementated using Matlab (see the corresponding codes)

Subsystem1.jpg

and the corresponding equations (for more detailed information see our establishment of the model).

FliA dynamics.jpg
CFP.jpg
YFP.jpg
RFP.jpg

where CFP, YFP, and RFP will be denoted below as respectively Z1,Z2 and Z3.

  • We wanted to see if our predictions were accurate or not. We then solved the equations, forcing the behavior of FhlDC. In a first step, we imposed a constant production term of 1. Then, at a certain time, we set this production term to zero :
FlhDC Test FIFO cresc.jpg
FlhDC Test FIFO decresc.jpg

In fact we assumed that this behavior for FlhDC was acceptable regarding its estimated behavior in the whole system.

  • We saw previously that without FliA, the FIFO would presumably not work. We then simulated a first system, where [FliA] stays to zero value.
Essai without fliA.jpg

We may see that there is a LIFO behavior rather than the FIFO we expect...

  • Then, we simulated the entire system, to check if we had
    • the lasting burst due to FliA (more important for Z3 than for Z2, and more important for Z2 than Z1) in the increasing phase.
    • the effect of fliA which maintained the concentrations to their maximum (more important for Z3 than for Z2, and more important for Z2 than Z1) in the decreasing phase.
Essai with fliA.jpg

  • We observe on these plots that the behavior is quite the one we expected, and that the FIFO is realized. FliA enables the curves to cross, and adds a delay on the genes that are most affected, with gives a better observability of the FIFO behavior.

Synchronization

Mathematical Analysis

Simulations and verification of the hypothesis