Team:Hawaii/Ligation of pRL1383a Parts

From 2008.igem.org

Revision as of 20:12, 6 October 2008

Birds Eye  View Team	Projects	Events	Resources
Sponsors	Experiments	Milestones	Protocols
	Notebook (t)	Meetings (t)

Ligation of Parts

• The BioBrick parts of pRL1383a are to be ligated in a series of experiments.

Methods

Restriction Digest

• Each part is digested with both enzymes. For all cases NEBuffer 2 is used.

• Reaction Conditions:

• 5ul Buffer
• 1ul Enzyme 1 + 1ul Enzyme 2
• 0.5 ul BSA
• Xul water
• Yul insert (1ug if possible)
• Zul vector (less than 1ug)

• Running Conditions: 2 hours at 37°C.

• Check the progress of the reaction by running a 0.8% gel.

Ligation

• Refer to http://openwetware.org/wiki/DNA_ligation for the reasoning behind this.

Transformation

Verification with Colony PCR

• Reaction conditions: 10ul volume: 5ul green taq, 4ul water, 1ul primers (VF2+VR)+ a sterile poke from a colony.
• Running conditions: 94 hold, [95 30", 62 30", 72 (time varies based on size of verification site)]x 30 cycles, 72 10', 4 hold.

Results

7/27

• A few re-digests and ligations were performed today: oriT + pSB1A3, oriV + pSB1A3, mob + B0024, rep + R0010, aadA(pRL1383a+R0010). Afterwards, the ligation product was transformed to DH5-alpha. Only OriT transformed. I did not check the progress of this experiment with a gel, so I am not sure where this went wrong.
• Next time, a gel will be run after every step.

8/11

Restriction digest from 8/11/08.

Ligation products from 8-11 ligation.

Transformation & Verification PCR

PCR verification of colonies from transformation with plasmids containing rep, P1 lytic region, the aadA (BB&pRL1383a) region, and oriV.

• The only bands corresponding to the correct size are the 4 oriVs and the 4th BB version of aadA.
• The rep region lanes are all either 300 or 600bp when they should be 3.3kb. If the RBS (B0030) ligated back to itself, the band should be 253bp. The bands at 300bp may be explained by this. It is unclear what happened in the latter case. The incorrect aadA bands are also around 300bp which would mean the RBS containing vector ligated back to itself some how. B0030 was cut with SpeI and PstI.

Plasmid Prep

• OriV1-4 and aadA (BB) were cultured over-night in Terrific Broth with amp100 as selection.
• The plasmids were isolated using an Alkaline Lysis Mini-Prep.

8/13

PCR verification of rep, P1lytic, and aadA from pRL1383a from 8/14/08.

PCR verification of aadA from pRL1383a.

• Three ligations were performed today. I checked my math from the last ligation and decided it wasn't totally correct for the rep ligation to B0030.
• P1 lytic was ligated to B0015 (TT), Rep to B0030 with precisely 2:1 insert to vector ratio, and the aadA region from pRL1383a to B0030.
• Unfortunately there is no gel to confirm this ligation.

Transformation

• The ligation products were transformed into DH5-alpha cells with selection on LB amp100 plates. pUC18 was transformed into DH5-alpha cells as a positive control, while no plasmid was used in a transformation as a negative control.
• A lawn of colonies was observed for all three transformations. No colonies grew for either control (need to check pUC18 and see if there are problems with our stock).

PCR Verification

• The rep region, as with the last ligation was not inserted to the vector. The band at 300bp suggest the B0030 vector was amplified by VF2&VR. Another possibility is that some of this plasmid was not digested and the ligation just did not work, so these were the only circular plasmids available for transformation.
• The P1 lytic region is at 400kb while the verification size of B0015 is 445bp...
• aadA from pRL1383a is amplified to several different sizes. One of which is about correct (~1kb), one above 10kb, and one at 0.25kb.

9/2

PCR for size verification for sequencing.

9/6

• 3A-(ish) ligation is going to be used for subsequent ligation reactions.
• The lac promoter and RBS have been synthesized. They were ligated together 1:1.
• The other parts are to be digested out of plasmid or PCR amplified and restriction digested to give the correct over-hangs.
  • Vector: E,P
  • Front part: E,S
  • Back: X,P

9/19/08

• Psuedo- 3A Assembly. This method is the same in that 2 pieces are assembled into a vector at one time, but differs in that the inserts are gel purified, so that the only plasmid involved is the recipient plasmid.

• Protocol:

The restriction digest products are run on a gel and then purified.

Ligation of 2 inserts into pSB1A3:replication proteins with promoter/RBS and promoter/rbs/aadA with terminator.

1. Restriction Digest: front insert (E,S), back insert (X,P), vector (E,P)
2. Purification/Preparation of Parts: the vector is de-phosphorylated with SAP and the inserts are gel purified, with the exception of parts <200bp, which are ligated directly
3. Ligation: at 16°C for 2 hours using T4 ligase.

Colony PCR from 9/20 and 9/21, results described in table.

Colony PCR from 9/20 and 9/21, results described in table.

Transformation of ligation Products

10/6

• Update on parts completed and those still in progress.

Individual Parts

This part was verified by PCR.

• Plac/RBS/rep in pSB1A3
• PCR verification of this part was compared to rep and the size difference determined that further verification was needed.

This amplicon was sent in for sequencing using a series of primers for full coverage of sequence. rep was previously sequenced and contained BioBrick sites and no mutations, except for a 50 bp region at 1500 bp. An additional primer was designed to cover this region.

• A glycerol stock of this part was made for long-term storage.
• XbaI and PstI were used to digest Plac/RBS/rep in pSB1A3. This digest was run on a gel and purified.

The band around 3478 bp was purified.

• The next step is to ligate this part to oriV.
• Today a plasmid prep of the glycerol stock was prepared to ensure that I have this part in stock and that the re-digest can be replicated.

Discussion

• Ligations into empty vectors seems to be successful, but when adding my part to an existing part, I run into problems.
• As a team we decided to synthesize the Promoters, RBS, and TT.

[http://manoa.hawaii.edu/ ][http://manoa.hawaii.edu/ovcrge/ ][http://www.ctahr.hawaii.edu ]

• Recent changes
• What links here
• Related changes
• Special pages
• My preferences

• Printable version
• Permanent link
• Privacy policy
• Disclaimers