Team:Heidelberg/Notebook/Visualization/Methods

From 2008.igem.org

(Difference between revisions)
(Swarm Assays)
(Swarm Assays)
Line 501: Line 501:
-
 
-
EXAMPLES:<br>
 
{| class="wikitable"
{| class="wikitable"
Line 508: Line 506:
|width=450px | [[Image:SwarmA_CA_line.jpg|350px|left]]  [[Image:SwarmA_CA_spot.jpg|350px|left]]
|width=450px | [[Image:SwarmA_CA_line.jpg|350px|left]]  [[Image:SwarmA_CA_spot.jpg|350px|left]]
| asd | asdf
| asd | asdf
 +
|}
 +
 +
 +
{| class="wikitable"
 +
|-
 +
| ''Examples:''
 +
|-
 +
|width=450px | [[Image:SwarmA_CA_line.jpg|400px|left]]  [[Image:SwarmA_CA_spot.jpg|400px|left]]
 +
|-
 +
|After ? hours
 +
|-
 +
|width=450px | [[Image:SwarmA_fluid_attractant.jpg|400px|left]]  [[Image:alternative_chamber.jpg|400px|left]]
 +
|-
|}
|}

Revision as of 20:11, 28 October 2008

Contents

Microscope

Small chamber

chemotactical activity

Large chamber

computer-assisted analysis

Swarm Assays

PROTOCOL FOR SWARM-PLATE CHEMOTAXIS AGAINST A POSSIBLE ATTRACTANT:
This protocol was created using petri-dishes. But every other chamber could be used as well.


  • Step 1: Make sure you have everything ready to get started. You need:
    • Petri-dishes. !!! sign your petri-dishes before You pour in the media. Also mark the spots where you want to set the attractant or attractant line and the bacteria. !!!
    • 50 ml falcons
    • 25 ml media containig 0.2%-0.3% Agar for every petri-dish.
    • samples of the appropriate attractants. The concentration depends on several substance depending attributes.
    • Other substances like antibiotics (Amp, Kan, Cm) or inducer (IPTG, Arabinose)
  • Step 2: Your agar-media solution should be clear and the agar completely solved. If you want to use attractant plugs1 or other non fluid attractants, go first through step 5 then back through 2,3,4 skip 5, further with 6 and so on...
  • Step 3: Take Take a 50 ml falcon pour 25 ml of your agar containing media in it and add antibiotics or inducing substances. If no extra substances are needed just skip this step.
  • Step 4: Let your media polimerize. At least let it rest for 15/20 min.
  • Step 5: Then add the attractant. e.g.: a casamino acid solution
  • Step 6:
    • Put the whole plate into a 4°C fridge for 12-16 hours to allow the attractant to build up a gradient.
    • Make an overnight culture of the strains you want to test, use TB media and add inducing substances if something has to be induced.

Next day:

  • Step 7: Take your overnight culture. It should be at an OD of 0.4-0.6. Then take 1 ml of the bacteria suspension and centrifuge it for 10 minutes at 4,000 rpm. Resolve the pellet at 100 µl of the media you are using in the petri-dish.
  • Step 8: Place 3-6 µl of your purrified bacteria at the premarked spots on the petri-dish sample.
  • Step 9: Put the whole plate into the incubator at ~30°C and take a look at your plates after 24, 48 and 72 hours. Put the plates into a plastic bag like the small ones for the bench trash to protect the plates from running dry to fast. Only move the plates if necessary.


1: Attractant plugs can be created by adding agar to the attractant solution.


SwarmA CA line.jpg
SwarmA CA spot.jpg
asdf


Examples:
SwarmA CA line.jpg
SwarmA CA spot.jpg
After ? hours
SwarmA fluid attractant.jpg