Team:UC Berkeley/LayeredAssembly

From 2008.igem.org

Revision as of 22:22, 29 October 2008

Project Motivation

Imagine a world with no mini-preps. A world where expensive cloning reagents were unnecessary. A world where DNA and protein extraction and purification could be accomplished in a single microcentrifuge tube. We did, and so we created Clonebots, an automated approach to synthetic biology.

Clonebots seeks to simplify and automate common laboratory procedures to protocols involving only liquid handling steps that can be readily performed by robots. We have accomplished this by genetically encoding many of the required steps into the E. coli, thereby allowing the cells to perform the required protocols in vivo. We worked on a wide variety of devices for these projects, and the details about our devices are described throughout this wiki. Most of our devices are associated with biologically encoding the reactions needed for standard assembly.

Layered Assembly

Our efforts to genetically encode standard assembly protocols centered around the layered assembly scheme used by the Anderson Lab at UC Berkeley. Layered assembly is a straight-forward and robust method for combining two or more basic parts into a destination vector. It involves three basic layers of procedure: Entry, Assembly and Destination. Both Entry and Assembly layers are standardized for ease of use, while the Destination plasmid can be tailored to a specific experiment or assay.

A schematic representation of Layered Assembly

Entry Layer

Biobrick parts are created in an entry vector. The Entry vector contains a Spectinomycin antibiotic resistance marker and Biobrick restriction sites (EcoRI, XbaI, and SpeI for the BBa standard; EcoRI, BglII, and BamHI for the BBb1 standard). The restriction sites are flanked by attR1 and attR2 recombination sites.

File:Entry plasmid

Since the entry plasmid contains attR recombination sites, the basic part can easily be transferred into one of six different assembly vectors using the Gateway cloning scheme.

Assembly Layer

The assembly layer is used to combine two or more basic parts in a specified order to create a composite part.

There are six assembly plasmids which contain two of three different antibiotic resistance markers (kanamycin, ampilicin and Chloramphenicol) separated by a XhoI restriction site. The basic parts are flanked by BglII and BamHI restriction sites.

The choice of antibiotic resistance markers in the assembly plasmids is predetermined such that once the two plasmids recombine, the new plasmid will have a combination of markers from the two assembly vectors. Although there are four possible products of this reaction, only one will have both of the correct antibiotic resistance markers.

The Clotho program developed by the UC Berkeley Comp team generates an assembly tree that minimizes the number of reactions required to make a composite part.

The assembly plasmids are transformed into cells that are engineered to either methylate BamHI or BglII restriction sites. Part A is transformed into a "lefty" cell that is methylated on BglII restriction sites while Part B is transformed into a "righty" cell that is methylated on BamHI restriction sites.

In a single eppendorf tube, lefty and righty plasmid DNA is combined, along with BamHI, BglII, XhoI restriction enzymes and ligase. Since restriction enzymes will not cut methylated DNA, the BglII restriction site in the lefty cell and the BamHI restriction site in the righty cell are blocked from digestion. The BamHI site in lefty and the BglII site in righty, and the Xho sites in both plasmids will be cut. Ligase will join the Xho sites and the BglII/BamHI complimentary sticky ends to create a composite part with a different combination of antibiotic resistance genes than either parent plasmid.

The assembly reaction can be repeated to combine a number of basic parts in a desired order.

Once the composite part is complete, it is transferred to a destination plasmid.

Destination Layer

Completed composite parts are transferred from the assembly layer to the destination layer using the Gateway cloning scheme. The destination plasmid is tailored to a specific experiment or assay. This allows a single composite part to be transfered to several different destination plasmids for further experimentation or characterization.

File:Destplas

Issues with Current Methods

1. Current protocols work well for BBa parts, but not as well for BBb. Clonebots used BBb because BBa cloning requires several complex procedures while BBb has the potential to be fully automated. By using methylated plasmids, BBb assembly can be compartmentalized to a single tube or cell.
2. Gateway reactions, used for transferring basic parts into the assembly plasmids and transferring composite parts into destination plasmids, are expensive ($8.65/reaction).
3. Current protocols with no gel purification step are inefficient. Protocols involving gel purification and background subtraction steps to screen for the correct parts after assembly cannot be fully automated.
4. Mini-preps are time-consuming and expensive.
5. People are more prone to make mistakes, i.e. switch tubes, use the wrong enzymes, etc. than robots.

Clonebots Solutions

1. Engineer cells to express their own integrase (Int), excisionase (Xis), and integration host factor (ihf) enzymes to perform in vivo Gateway reactions.
2. Eliminate mini-prep steps from cloning protocols by using our lysis device and in vivo assembly.
3. Engineer cells and plasmids to express their own BamHI, BglII, Cre restriction enzymes and ligase so that assembly reactions in cell lysate and in vivo are possible.
4. Develop protocols that involve only liquid handling steps, so that cloning can be automated, requiring less money and labor.

• Recent changes
• What links here
• Related changes
• Special pages
• My preferences

• Printable version
• Permanent link
• Privacy policy
• Disclaimers