Team:Paris/Modeling/Protocol Of Characterization

I-Principles of the Experiments

To evaluate quantitativly the activity of a promoter in function of its transcription factors, we need data in which the different values of the activities are correlated with various known and controlled values of the transcription factors concentrations.

Therefore, we designed a generic plasmid in which the transcription factors are put under the control of previously characterized inducible promoter, and the studied promoter is put before a fluorescent reporter gene. In order to allow the study of the influence of two transcription factors over the tested pormoter, we chose to put the tested transcription factor (also called the "tested gene" in the following) under two different inducible systems . One is the pBAD-AraC system. The second one is an indirect system were the gene is after the Tet inducible promoter pTet.

The TetR gene would be expressed constitutively and at high rate thanks to a strong promoter (J23101) and its influence over the pTet promoter would be regulated by the concentration of the aTc molecule. That way, the production of the tested transcription factor can also be regulated, because the J23101, and the pTet have been previously characterized. In a quite similar way, we characterize the pBad promoter.

Here we show the design of two plasmids : one to test the influence of one gene and the other to test the influence of two genes over the tested promoter.

II-Plasmid for promoter characterization

II-A-For study with one Transcription Factor

II-B-For study with two Transcription Factor

III-Molecular design for Promoter Characterization Plasmid

Our aim is to make this plasmid useful not only for our project but for the whole iGEM comunity. This is why we decided to keep the Biobrick spirit as much as we could, making the plasmid compatible with the parts, so the teams using it needs only the four traditional enzymes: EcoRI, XbaI, SpeI and PstI.We wanted also to make optional the introduction of a second tested transcription factor. The strategy is then based in two plasmids.

The principal plasmid contains everything needed to test the effect of one gene over the tested promoter activity. The second plasmid called « Accessory plasmid » can be introduced easily in the Principal Plasmid and contains the necessary elements to add the expression of a second gene to the system. The resulting plasmids are presented below.

↓ III-A-Principal plasmid ↑

↓ III-B-Accessory plasmid ↑

IV-Promoter and Transcription Factors insertion

The strategy to introduce the tested promoter and the tested transcription factor(s) is very simple. The only difficulty is that the order of insertion that we describe has to be respected to avoid unwanted restriction enzyme cuts:

V-Resulting plasmids

V-A-For one transcription factor effect

V-B-For two transcription factors effect

VI-Protocole for plasmid construction

We show here our plan to make these plasmids at the experimental level.

VI-A-Principal Plasmid construction

We devided the Principal Plasmid in two main blocks to go faster:

VI-A-1-Blocks

↓ VI-A-2-Block 1 construction ↑

the result...

↓ VI-A-3-Block 2 construction ↑

Biobrick assembly steps: Restriction sites addition by PCR:

↓ VI-A-4-Two-block assembly ↑

VI-B-Accessory plasmid construction

Addition of restriction sites to B0015 by PCR:

↓ Scheme ↑

Addition of restriction sites to pBAD-AraC by PCR:

↓ Scheme ↑

Assembly:

↓ Scheme ↑

Specific Assumptions for the Experiments

The previous experiment is used to find parameters regarding to our modelization. However, the experiments themselves must be described in the same way to interprete these parameters consistently.

In this order, the two inductible promoters will be described exactly as the others (those in the system), with similar rules of complexation and transcription.

Otherwise, as we control the quantity of transcription factor by the introduction of small molecules, we must model the diffusion/complexation/induction phenomena, which lead from the latter to the former. By putting the cell culture in a chemostat, we will be able to control precisely the concentration of the input small molecules. At quasi steady-state, and assuming a simple, passive and quick diffusion, we consider the inner concentration, the outer medium concentration, and the input concentration beeing all equal.

↓ Quick Mathematical Development ↑

Thus, if we consider these "rules" it gives at quasi steady-state resulting in the following analytical expression of [Compl] and [Prot] : ...that we can introduce in the expression of the activity of pTet and pBad in function of their transcription factor.

Thanks to these considerations, we can have access to these characterizations :

and then